How to Set Up Wedge Grips: Jaw Faces, Alignment and Stopping Slippage
Created at : Sep 9, 2026Wedge grips are the most common grips on any universal testing machine, and also the grips most often blamed for bad results. Nearly every wedge grip problem comes down to the same few things: the wrong jaw face, a specimen set too shallow or off-center, worn serrations, or a grip that is too big or too small for the job. This guide covers how wedge action works, how to choose jaw faces, a step-by-step setup routine and how to fix slippage and jaw breaks.
If you are still deciding which grip family suits your specimen, start with our overview of the types of tensile testing grips.
How Wedge Action Works
Two jaws ride in a tapered housing. When you close the grip, the jaws slide down the taper and touch the specimen. When the test begins, the pull on the specimen drags the jaws further into the taper, and the taper converts that pull into side force on the specimen. The harder the test pulls, the harder the jaws squeeze. That is why a correctly set wedge grip almost never lets go of a steel bar, even near the top of its rating.
Two consequences matter for setup. First, the initial bite only needs to be enough to start the wedge action; the load does the rest. Second, because the squeeze grows with load, anything that concentrates stress at the jaw edge (sharp serrations on a soft specimen, a specimen clamped too close to its radius) gets worse as the test goes on.
Video: Mechanical wedge grips: closing and loading a specimen
Manual, Pneumatic and Hydraulic Wedge Grips
| Type | How the jaws close | Good for | Our options |
|---|---|---|---|
| Manual | Lever, knob or crank moves the jaws into the taper | General metals and plastics, moderate test volume | 5 kN, 10 kN, 20 kN, 50 kN, 50 kN with crank, 100 kN, 100 kN high capacity, 150 kN, 300 kN |
| Pneumatic | Air cylinder closes the jaws at a set pressure | High test volume, consistent pre-grip between operators | Pneumatic wedge grips |
| Hydraulic | Oil pressure closes the jaws with a set force | High-strength steel, rebar and fasteners at high force | 300 kN hydraulic wedge grip |
Manual grips are the lowest cost and need no utilities. Pneumatic and hydraulic closing make the initial bite the same every time, which removes a real source of operator-to-operator scatter, and save effort when the jaws are large. Above roughly 100 kN, manual closing of large jaws becomes slow and tiring, which is why high-capacity labs move to hydraulic.
Video: How to use 100 kN high-capacity wedge grips
Choosing Jaw Faces
Jaw faces are the replaceable inserts that touch the specimen. Picking the right face fixes more slippage and jaw-break problems than any other single change.
| Specimen | Typical jaw face | Why |
|---|---|---|
| Flat steel and hard metals | Coarse serrated (pyramid or file-cut) | Deep bite resists slip at high force |
| Aluminum, copper, softer metals | Fine serrated | Enough bite without tearing the surface |
| Round bars and rod | V-groove faces sized to the diameter | Centers the bar and contacts it along two lines |
| Rigid plastics (ASTM D638) | Fine serrated or light-texture faces | Coarse teeth start cracks in brittle plastics |
| Composites (ASTM D3039) | Fine serrated or surfaced faces with tabbed coupons | Tabs spread load and protect fibers |
| Coated or finished surfaces | Smooth or rubber-faced | Avoids marking and coating damage |
Every jaw face covers a range of thickness (flat) or diameter (round). A specimen near the bottom of the range may not engage the taper fully; one near the top may stop the jaws short of the working zone. Check the range on the grip page, and keep faces for each size you test.
Step-by-Step Wedge Grip Setup
- Check the grip rating. Peak force should sit comfortably inside the grip, load cell and frame ratings.
- Inspect and clean the jaw faces. Brush out scale and debris. Replace faces with rounded or chipped teeth.
- Lubricate the wedge surfaces per the grip instructions so the jaws slide freely and release after the test.
- Align the grips. Upper and lower grips must share one load line. Check the clevis pins and any adapters for play.
- Set the grip separation to the gauge or grip length the standard calls for.
- Insert the specimen to full depth. Use specimen stops or marks so every specimen sits at the same depth, at least most of the jaw length.
- Center the specimen across the jaw width. An off-center specimen bends as it loads.
- Close the upper grip first, zero the load, then close the lower grip. This avoids clamping in a pre-load.
- Attach the extensometer if strain is measured. See the clip-on extensometer guide.
- Run the test and inspect the break. A break in the gauge length is valid. A break at the jaw edge needs investigation.
Fixing Slippage in Wedge Grips
Slippage shows on the load curve as a sudden drop and recovery (a sawtooth), or as extension that keeps climbing while load stays flat. You will often see polished streaks on the specimen at the slip zone.
| Cause | Fix |
|---|---|
| Worn or clogged serrations | Clean or replace the jaw faces |
| Specimen too thin for the jaw range | Use the correct face size or add shims |
| Shallow insertion | Insert to full jaw depth with a stop |
| Initial bite too light | Close more firmly, or raise pneumatic or hydraulic pressure |
| Very hard or smooth surface | Coarser serrations; consider hydraulic closing |
| Dry or galled wedge surfaces | Clean and lubricate the taper so the jaws can advance |
Fixing Jaw Breaks
A jaw break is a failure at or inside the jaw edge. Most standards treat it as an invalid result or require a note. Causes are almost always stress concentration at the jaw:
- Serrations too coarse for the material. Step down to fine serrated or smooth faces.
- Specimen not shaped for gripping. Use dumbbell specimens cut with a precision cutting die, or bond tabs on composites.
- Misalignment adds bending at the jaw. Recheck the load line.
- Too much pre-grip pressure on pneumatic or hydraulic grips. Lower it in steps until slippage just stops.
- The material simply suits a different grip. Soft, notch-sensitive materials often belong in vise or roller grips.
For problems that are not specific to wedge grips, such as machine misalignment or strain errors, see our tensile test troubleshooting guide.
Standards Commonly Run in Wedge Grips
- ASTM E8: tension testing of metallic materials. Full walkthrough in our ASTM E8 guide.
- ASTM A370: mechanical testing of steel products, including bar and rebar.
- ASTM D638: tensile properties of plastics. See the D638 guide.
- ASTM D3039: tensile properties of polymer matrix composites.
- ASTM A416: steel strand for prestressed concrete (special strand jaws).
Browse every method-specific fixture in our ASTM-specific grips hub, or the full wedge grip line.
Frequently Asked Questions
How do wedge grips work?
The jaws sit in a tapered housing. As the test pulls on the specimen, the jaws are drawn deeper into the taper and clamp harder, so grip force rises with test force.
Why does my specimen slip in wedge grips?
The usual causes are worn or clogged jaw faces, a specimen too thin for the jaw range, shallow insertion or too light an initial bite. Clean or replace the faces, insert to full depth and close firmly.
Why do my specimens break at the jaws?
Stress concentration at the jaw edge. Use finer or smooth faces, dumbbell or tabbed specimens, correct alignment and lower pre-grip pressure. Soft materials may need vise or roller grips instead.
Which jaw faces should I use for round bars?
V-groove faces sized to the bar diameter. They center the bar and grip it along two lines of contact.
When should I choose hydraulic wedge grips?
For high-strength steel, rebar and fasteners at high force, or when you need the same pre-grip force on every test without manual effort.
Should I close the upper or lower grip first?
Close the upper grip first, zero the load reading, then close the lower grip, so clamping does not leave a pre-load in the specimen.
Get a quote
Interested in an immediate price quote or an application discussion? Email christhomas@universalgripco.com or frank@universalgripco.com, or call or text us at 978-882-1480. Tell us the material, specimen size and peak force, and we will recommend the wedge grip capacity and jaw faces for your machine with a firm price.