ASTM D4964

Introduction

ASTM D4964 outlines the standard test method for measuring the stretch (elongation) and recovery of elastic fabrics using a tensile testing machine. This test is critical in evaluating the performance of fabrics used in activewear, medical textiles, automotive applications, and compression garments, where elasticity and the ability to return to original dimensions are essential.

This guide provides a step-by-step explanation of how to perform the ASTM D4964 test, including equipment requirements, sample preparation, test parameters, and interpretation of results. Following the correct test protocol ensures accurate measurement of elongation properties and recovery behavior under cyclic tensile loading.

Overview of ASTM D4964 Procedure

ASTM D4964 measures two key properties:

• Stretch (Elongation) – How far the fabric can be extended under tension.

• Recovery – How well the fabric returns to its original length after being stretched.

The standard allows for single or multiple cycles of extension and recovery. Measurements are typically taken at set intervals (e.g., after 1, 2, or 3 cycles) to assess both immediate and delayed recovery performance.

Equipment and Materials

1. Universal Testing Machine (UTM)

• The test requires a tensile testing machine capable of controlling crosshead speed and measuring force and extension with high resolution.

• A low-capacity load cell (typically 10 N to 500 N) is suitable, depending on the stretch strength of the fabric.

2. Grips

• Use pneumatic or mechanical grips with wide, flat faces (25 mm to 75 mm) to distribute pressure evenly and avoid sample slippage or damage.

• Grips should have rubber-faced or serrated jaws to securely hold flexible fabric specimens without tearing.

3. Elastic Fabric Specimens

• Specimens must be conditioned and cut to precise dimensions according to the standard.

• Typically, specimens are cut to 50 mm (2 in.) wide and 200 mm (8 in.) long, with the long axis aligned to the stretch direction.

Specimen Preparation

1. Conditioning:
   Condition all test specimens in a standard laboratory environment of 21 ± 1°C and 65 ± 2% RH for at least 4 hours prior to testing.

2. Sample Cutting:
   Cut fabric specimens in the direction of greatest stretch, usually the machine or cross direction as specified by the user.
   Ensure clean edges without fraying, using a cutting die or rotary blade.

3. Marking:
   Mark two reference lines on the specimen at a known distance apart (typically 100 mm) in the test area. This enables visual measurement of extension and recovery length.

Test Procedure

1. Mounting the Specimen

Secure the fabric specimen vertically in the grips with the reference gauge length (100 mm) centered between the jaws.
Ensure alignment is straight with no slack or twists in the sample.

2. Stretching Phase

Extend the specimen at a constant crosshead speed of 300 ± 10 mm/min to a specified extension level (usually 20%, 50%, 100%, or as defined by the user).
Hold the specimen in the extended position for 1 minute (or as specified).

3. Recovery Phase

Release the load or return the grips to the original gauge length.
Hold the specimen in the relaxed state for a defined recovery time (e.g., 1 minute, 5 minutes, or longer).
Measure the recovered distance between the gauge marks.

4. Repeat Cycles (Optional)

For cyclic testing, repeat the stretch and recovery sequence for 2 or more cycles to assess delayed recovery or fatigue behavior.

Calculation of Results

ASTM D4964 defines two primary performance metrics:

Percent Stretch (Elongation):

Percent Stretch = ((Length under tension – Original gauge length) ÷ Original gauge length) × 100

For example, if the original gauge length is 100 mm and the fabric stretches to 125 mm under tension, then:
Percent Stretch = ((125 mm – 100 mm) ÷ 100 mm) × 100 = 25%

Percent Recovery:

Percent Recovery = ((Length under tension – Length after recovery) ÷ (Length under tension – Original gauge length)) × 100

For example, if the stretched length is 125 mm, original gauge length is 100 mm, and length after recovery is 105 mm, then:
Percent Recovery = ((125 mm – 105 mm) ÷ (125 mm – 100 mm)) × 100 = (20 ÷ 25) × 100 = 80%

Higher recovery percentages indicate better elastic performance.

Reporting Requirements

The test report should include:

• Type of fabric and direction of stretch

• Number of test cycles

• Maximum extension level (percent elongation)

• Crosshead speed

• Percent stretch and percent recovery per cycle

• Time at maximum extension and recovery time

• Temperature and humidity during testing

• Observed failure modes or permanent deformation

Common Applications

• Athletic and compression garments (e.g., yoga pants, shapewear)

• Medical textiles (e.g., bandages, wraps)

• Elastic components in automotive and upholstery

• Textile R&D and quality control

ASTM D4964 testing helps manufacturers optimize material selection, ensure long-term garment durability, and compare competitor product performance.

Safety and Best Practices

• Do not test excessively narrow or damaged samples, as they may slip or tear in grips.

• Verify load cell calibration before each test series.

• Apply grip pressure evenly across the sample width to avoid premature edge failure.

Conclusion

The ASTM D4964 test method provides a standardized, reliable procedure for evaluating the tension and recovery properties of elastic fabrics. This test is especially valuable for manufacturers of performance apparel, medical textiles, and flexible technical materials where stretch and shape retention are critical.

Proper specimen preparation, grip selection, and control of test parameters ensure accurate, repeatable results. Engineers and quality assurance professionals can use this data to validate material consistency, monitor production quality, and inform product design.​